Maintenance Club

Why Join Our Maintenance Club?

Priority Service

Get priority scheduling during high-demand seasons and faster response times for service calls.

Expert Maintenance

Comprehensive twice-yearly preventative maintenance to keep your system running at peak efficiency.

Exclusive Discounts

Save 10-20% on all service repairs and enjoy special member pricing on equipment upgrades.

Choose Your Membership Level

Select the plan that best fits your needs and budget

Silver Club

$12.50/month

or $150/year

Twice yearly preventative maintenance service

Priority high demand service calls above non-contract customers

10% off all service repairs

Gold Club

$25/month

or $300/year

All Silver Club benefits

Two times annual filter changes with 1" pleated air filters plus two additional filters

One time annual filter change for 4" or 5" filter housing

Condenser and Evaporator coil cleanings

Platinum Club

$50/month

or $600/year

All Silver & Gold Club benefits

10% Off Carrier Equipment

20% Off All Service Repairs

Diagnostic Fee Credit

*Additional cost for more than one unit. Contact us for multi-unit pricing.

Comprehensive Maintenance Checklist

Our thorough inspection process ensures your system runs at peak performance

Spring/Summer Cooling Season Maintenance

Check air filter cleanliness (Dirty air filters cause poor operation)

Check dual run cap for corrosion and proper tolerance (protect motors and compressors)

Check contactor for pitting / arcing (Premature compressor failure)

Check refrigerant charge (Optimize heat transfer)

Check condenser coil for cleanliness (Higher compressor amperage)

Check condenser fan motor amp draw and bearings

Check evaporator coil for leaks and corrosion (Refrigerant leaks and freeze-ups)

Check drain lines for proper flow (Ruined sheet rock and ceilings)

Check system for proper slope (Improper drainage)

Check main control board for signs of corrosion and terminal connections (Inconsistent operations)

Check blower amp draw and bearing seals (Overheating motor off on overload)

Check blower wheel balance (Vibration leads to bigger problems)

Check thermostat low voltage wiring connections and program set back schedule (Prevent nuisance calls)

Check damper motors for proper function (Optimal air distribution)

Check zone controls for proper function (Optimal air distribution)

Check duct work integrity (Optimal air flow consistency)

Check primary drain pan integrity (Prevent leakage into the home)

Check secondary drain pan integrity (Prevent leakage into the home)

Check Drain Pan for safeties (Prevent leakage into the home)

Check temperature splits (Looking for 20° cool and 45° heat. Maintain factory design parameters)

Inspect suction line insulation (Prevent water leaks and proper heat transfer)

Fall/Winter Heating Season Maintenance

Check air filter cleanliness (Dirty air filters cause poor operation)

Check blower run cap for corrosion and proper tolerance (protect motors and compressors)

Check flame sensor for cleanliness (Prevent nuisance calls)

Check pressure switch for proper function (Prevent nuisance calls)

Check inducer motor amp draw (Overheating motor off on overload)

Check gas valve function (Failure to open causes no flame)

Check ignitor for corrosion (Ensures proper system ignition)

Check flame consistency (proper fuel / oxygen mix)

Check heat exchanger integrity (Causes system failure - safety)

Check furnace safety switches (Verify shut down due to malfunction)

Check (heat pump) refrigerant (Optimize heat transfer)

Check (heat pump) condenser coil for cleanliness (Higher compressor amperage)

Check (heat pump) condenser fan motor amp draw (Motor failure can lead to compressor failure)

Check (heat pump) evaporator coil for leaks and corrosion (Refrigerant leaks and freeze-ups)

Check drain lines for proper flow (Prevent water intrusion)

Check system for proper slope (Improper drainage)

Check main control board for signs of corrosion and terminal connections (Inconsistent operations)

Check blower amp draw and bearing seals (Overheating motor off on overload)

Check blower wheel balance (Vibration leads to bigger problems)

Check thermostat low voltage wiring connections and program set back schedule (Prevent nuisance calls)

Check damper motors for proper function (Optimal air distribution)

Check zone controls for proper function (Optimal air distribution)

Check duct work integrity (Optimal air flow consistency)

Check temperature splits (Looking for 20° cool and 45° heat. Maintain factory design parameters)

Inspect suction line insulation (Prevent water leaks and proper heat transfer)

Award & Associations

BuildZoom.com

HVAC/Mechanical Contractors in Rocklin

Ready to Join the Maintenance Club?

Protect your investment and ensure year-round comfort with our expert maintenance services